Options

4th Axis

Hardware and software that allows true 4th axis interpolation. Includes indexer, tailstock and fixture plate.

4th Axis

Advanced Features with Verify

Advanced Features with Verify incorporates 3D solid model machining simulation software that allows you to quickly and easily proof your ProtoTRAK mill and lathe programs prior to cutting chips.

Advanced Features with Verify

Auto Lubrication Pump

The auto lubrication for the ways and ballscrews is wired to operate while the spindle is running. Discharge times and intervals are set on the lube pump.

Not available for model K3EMX Knee Mills.


Auxiliary Functions

The Auxiliary functions provide program control of spray mist or coolant, spindle off, and interface to a programmable rotary table or indexer.

Standard on model FHM7 Bed Mill.

Not available for models K3EMX and K3SMX Knee Mills.


Ball Lock Clamping Device

Set of four.

A set of four is included standard on the TRAK LPM.

Available as an option on the TRAK 2OP.

Ball Lock Clamping Device

Ball Lock Liners Primary – Set of Eight

For fixture plates. High precision for use with Primary Locating Holes in the TRAK LPM and TRAK 2OP tables.

Ball Lock Liners Primary – Set of Eight

Ball Lock Liners Secondary – Set of Eight

For fixture plates. Lower precision for use with Secondary Locating Holes in the TRAK LPM and TRAK 2OP tables.

Ball Lock Liners Secondary – Set of Eight

Ball Lock Locating Guide Assembly

For locating your current fixtures on the LPM table using the ball lock system and locating holes on the table. Includes three stops.

Ball Lock Locating Guide Assembly

Chip Pan

Chip pan for TRAK Knee Mills.

Chip Pan

Chip Tray / Splash Shield

Chip tray and splash shield installed at the factory (recommended).

Chip Tray / Splash Shield

Chuck

Direct-mounting chuck features separate top jaws and master jaws. The chuck is rated for the top RPM of the lathe.

Lathe Model     Size      Chuck Through-hole      Spindle
1440EX              6"          1.575"                                 D1-4
1630SX              8"          1.969                                  D1-6
1630HSSX         6"          1.77"                                   A2-4
1845SX              8"          1.969"                                 D1-6
2470SX              12"        4.160"                                 D1-8

Chuck

Collet Closer

Lathe Model      Type
1440EX               5C Taper Mount, Extended Nosepiece
1630SX               5C Taper Mount, Extended Nosepiece
1630HSSX          5C Taper Mount, Extended Nosepiece
1845SX               5C Taper Mount, Extended Nosepiece


Converter - DXF File

Powerful software that imports DXF file information and provides the user interface to add the data necessary to complete the part program. Same user friendly format as the ProtoTRAK programming

Not available for EMX / ELX CNC model machines.

Converter - DXF File

Converter - Parasolid

The powerful Parasolid Converter makes it easy for you to generate ProtoTRAK mill programs from Parasolid 3D CAD files.  Contact your sales rep for more details.

Not available for model K3EMX Knee Mills.

Converter - Parasolid

Coolant Pump

The optional coolant pump is mounted on the back of the machine column. It is wired into the electrical panel for operation as an auxiliary function or through the Accessory key on the CNC front panel. A manual switch is provided for ProtoTRAK SMX CNC two-axis models, or if Auxiliary Function option is not ordered.


Dorian 8 Position Indexer

Dorian brand, model Smart-Dex 20 or 25 installed and integrated into the machine. Eight stations, coolant supplied at each tool.

Comes with 2 ea boring bar holders.

  • 3/4" Indexer P/N BBH20-125-3
  • 1" Indexer P/N BBH25-150-3

Also shown with 2 additional boring bar holders and 4 cutting tools, not included.

Lathe Model        Tooling
1630SX                 3/4"
1630HSSX            3/4"
1845SX                 3/4" or 1"
2470SX                 1"

Dorian 8 Position Indexer

Faceplate

300mm, slotted. Mounted by the D-1 camlock.

Lathe Model       Diameter
1440EX                10"
1630SX                12"
1845SX                14"
2470SX                20"

Faceplate

Fixture Cart

High quality cart by Huot Manufacturing. Lip height and length matches LPM table position during fixture change.

Fixture Cart

Fixture Plate

Precision plate with primary liners. Made of aluminum tooling plate that resists warping.

Alpase K100 or Alcoa Mic6

TRAK LPM - Available in three sizes:

  • Small (shown) - 16" x 15.5"
  • Medium - 16" x 24"
  • Large - 16" x 32"

TRAK 2OP

  • 18" x 15"
Fixture Plate

Follow Rest

Solid brass nib type.

Lathe Model       Max Workpiece Dia.
1440EX                1.97"
1630SX                5"
1630HSSX           4"
1845SX                4"
2470SX                6”

Follow Rest

Glass Scale

A popular brand of glass scale  mounted on the table and saddle.

Glass Scale

Halogen Work Lamp

Convenient light with bright, long lasting halogen bulb.

Halogen Work Lamp

Headstock Oil Cooler - Model 2470SX

An optional oil pump that circulates the headstock oil through an external cooler.  Recommended on machines that are run at high RPM’s for extended periods of time.


Knee Power Feed

Knee power feed for TRAK Knee mills.

Knee Power Feed

Limit Switches

Switches and brackets to set for maximum travel limits. Tripping the switch will cause the servo motors to shut down. Note, limit switches are not especially recommended. The system software monitors voltage intensity and will shut down the servos if it detects excessive force.


Mobile Tool Setting Cart

One comes with every LPM, you would buy this only if you want an additional cart.

Standard with TRAK LPM (shown).

Optional for TRAK 2OP.

Mobile Tool Setting Cart

Networking Option

The Networking Option lets you connect your ProtoTRAK to a network of other ProtoTRAKs or offline computers.

Not available for EMX / ELX CNC model machines.


Power Draw Bar

A Torque-Rite brand power draw bar factory installed on your machine. May be ordered as CAT or NMTB/NST. The draw bar for the CAT type is longer to fit into tool holders that have the tool changer grip, or retention knob, removed. Highly recommended.

Power Draw Bar

Retention Knobs

Set of 16.

TRAK LPM - CAT 40

TRAK 2OP - 30 Taper

Retention Knobs

Riser Block

Riser block for TRAK Knee mills.

RISER-4 (for 4")
RISER-6 (for 6")
RISER-8 (for 8")


RSG - The Remote Stop/Go Switch

Our most popular accessory. A convenient hand-held switch to start and stop the CNC servos during program run.

RSG - The Remote Stop/Go Switch

Spray Coolant

The unique Fog Buster non-fogging coolant sprayer precisely directs a fine stream of coolant to the tool and workpiece.

Spray Coolant

Star 4-Position Indexer

Integrated into the ProtoTRAK SLX CNC. Four stations that index with the control command.

Lathe Model       Tooling
1630SX                3/4"
1630HSSX           3/4"
1845SX                3/4" or 1"
2470SX                1"

Star 4-Position Indexer

Steady Rest

Model          Diameter (inches)     Type
1440EX        .20 to 2.36                   Roller
1630SX        .500 to 5.5                   Roller
1630HSSX   .500 to 5.5                   Roller
1845SX        .0.4 to 7.78                  Roller
2470SX        1.5 to 8.00                   Roller

Steady Rest

Tableguard

Table guard with sliding doors to impede chips and coolant and keep the operator from the tool and workpiece during CNC machining. Interlock switch on the door interfaces to the CNC. DRO and TRAKing are allowed with the door open, but the door must be closed for automatic CNC operations in the Program Run Mode.

Tableguard

Tailstock

Optional for the 1630SX and 1630HSSX, standard on all other lathe models

Tailstock

Tooling Kit

Dorian brand tooling kit. Contains a tool post and a variety of tool holders. The tool post has a release mechanism for quick, easy tool changes. It is repeatable within .001".

Lathe Model        Tooling
1440EX                 3/4"
1630SX                 3/4"
1630HSSX            3/4"
1845SX                 3/4" or 1"
2470SX                 1"

The tooling kit includes:

  • A quick-change tool post
  • 4 each 3/4" or 1" square tool holders for turning, facing and boring
  • 1 each #4 Morse taper drill holders
  • 1 each boring tool holder
  • 3/4" Tooling - Boring dia 1.000"
  • 1" Tooling - Boring dia 1.250"
Tooling Kit

TRAKing / Electronic Handwheel Option

This option converts the mechanical handwheels into electronic handwheels for operating the table and saddle which in turn enables the powerful TRAKing feature of the ProtoTRAK SMX CNC. The power comes in that you no longer have to choose between the efficiency of CNC and manual control - TRAKing gives you both. With TRAKing, you don't have to go through the process of proving out the CNC program before you press the Go button. You can run the CNC program at the speed at which you crank the handwheel. Go fast, go slow, stop and take a measurement, go backwards, whatever. You are in complete control as the machine moves the table, saddle and (for three-axis models) the quill through the programmed coordinates.

Standard on models FHM7 and DPM SX5P Bed Mills.

TRAKing / Electronic Handwheel Option

TRAKing Option

The power of TRAKing is that you no longer have to choose between the efficiency of CNC and the security of manual control - TRAKing gives you both. With TRAKing, you don't have to go through the process of proving out the CNC program before you press the Go button. You can run the CNC program at the speed at which you crank the handwheel. Go fast, go slow, stop and take a measurement, go backwards, whatever. You are in complete control as the machine moves the saddle and cross slide through the programmed coordinates.

Not available for the 1440EX Lathes.


USB Thumb Drive

The USB Thumb Drive option is a Delkin Devices 512MB thumb drive. It serves the following purposes:

  • Save program files for backing up or additional storage
  • Load program files
  • Share program files between ProtoTRAKs or computers
  • Save system configuration files, including backlash and calibration values

The thumb drive comes correctly configured for ProtoTRAK EMX/EXL interface and includes a copy to the PTEX Offline Programming software for making part programs on a PC.

USB Thumb Drive

Vise

6” Kurt vise and mounting hardware (Model 688 shown). Opens to 8.8”. Contact your sales rep to find the correct model vise for your machine.

Vise

Vise Fixture Plate

Includes plate, fence, stop and hardware. Does not include vise.

Vise Fixture Plate

Vise Stop

Includes mag base and 1", 2" and 3" extensions.

Vise Stop

Work Lamp

The optional work lamp is a 110 volt, 15 watt fluorescent light. The 18" light tube is mounted to the top of the splash shield just to the right of the spindle. The light is protected by a watertight polycarbonate tube that is sealed by an o-ring. A steel shield prevents damage from large flying objects and stainless steel armoring protects the electrical cable.

Available for current TRAK SX Lathes and as a retrofit for prior TRAK and Sport models 1440P and 1745P.