TRAK TMC7 Toolroom Machining Center

featuring the ProtoTRAK RMX CNC

TRAK DPM RX2 Bed Mill
TMC7 featuring the ProtoTRAK RMX CNC
  • TRAK TMC7 Toolroom Machining Center Front View
  • TRAK TMC7 Toolroom Machining Center - Three Quarter View
  • TRAK TMC7 Toolroom Machining Center
  • TRAK TMC7 Toolroom Machining Center - Figure 1
  • TRAK TMC7 Toolroom Machining Center - Figure 2

TMC7 Specifications

  • Table Size: 35.43″ x 19.69″
  • Travel (x, y, z): 30″ x 20″ x 20″
  • Footprint: 97″ x 135″
  • Horsepower: 15/10

The Versatile Machine That Works Two Ways

Toolroom Ops - when you need the TMC to work like a TRAK bed mill, but with chips and coolant contained
  • Optional Electronic Handwheels (x, y, and z)
  • Selectable 2 or 3 axis CNC
  • Full DRO for manual operations
Production Ops - when you need to run small to medium production quantities
  • 16-tool carousel tool changer along with manual tool change for additional tools
  • Convenient Tool Table fly out window
  • Fully enclosed ANSI compliant operation

Specifications All TMCs

  TRAK TMC5 TRAK TMC7 TRAK TMC10 TRAK TMC12 TRAK TMC14
Table size 27.56″ x 15.75″ 35.43″ x 19.69″ 44.09″ x 19.69″ 51.18″ x 23.62″ 62.99″ x 23.62″
Travel (X, Y, Z axis) with soft limits 20″ x 16″ x 20″ 30″ x 20″ x 20″ 40.75″ x 20″ x 20″ 50″ x 27″ x 25″ 60″ x 27″ x 25″
Rapid traverse X, Y, Z 400 IPM in Toolroom Ops
1,000 IPM in Production Ops
400 IPM in Toolroom Ops
1,000 IPM in Production Ops
400 IPM in Toolroom Ops
1,000 IPM in Production Ops
400 IPM in Toolroom Ops
1,000 IPM in Production Ops
400 IPM in Toolroom Ops
1,000 IPM in Production Ops
T-slots (number x width x pitch) 3 x .709″ x 3.937″ 5 x .709″ x 3.937″ 5 x .709″ x 3.937″ 5 x .709″ x 3.937″ 5 x .709″ x 3.937″
Spindle taper 40 Taper 40 Taper 40 Taper 40 Taper 40 Taper
Spindle speed range 50 - 8,000 RPM
50 - 12,000 RPM (optional)
50 - 8,000 RPM
50 - 12,000 RPM (optional)
50 - 8,000 RPM
50 - 12,000 RPM (optional)
50 - 8,000 RPM
50 - 12,000 RPM (optional)
50 - 8,000 RPM
50 - 12,000 RPM (optional)
Spindle nose diameter 3″ 3″ 3″ 3.75″ 3.75″
Tool clamping force (90 psi) 1,500 lbs 1,500 lbs 1,500 lbs 2,200 lbs 2,200 lbs
Tool holder type CAT 40 or BT 40 CAT 40 or BT 40 CAT 40 or BT 40 CAT 40 or BT 40 CAT 40 or BT 40
ATC tool capacity 16 16 16 16 16
Maximum tool weight (incl. holder) 15 lbs 15 lbs 15 lbs 15 lbs 15 lbs
Maximum tool diameter 3.14″ 3.14″ 3.14″ 3.14″ 3.14″
Carousel speed .8 sec from station to station .8 sec from station to station .8 sec from station to station .8 sec from station to station .8 sec from station to station
Tool selection system Bi-directional/shortest path Bi-directional/shortest path Bi-directional/shortest path Bi-directional/shortest path Bi-directional/shortest path
Spindle motor HP - peak 15 HP 15 HP 15 HP 22.5 HP 22.5 HP
Spindle motor HP - continuous 10 HP 10 HP 10 HP 15 HP 15 HP
Power requirements
Standard (208V)
8K Spindle
208V (200-240V is acceptable), 3P, 68A
(Current can be as high as 87 amps with all options ordered - CTS (+14A), 4th axis (+5A))
208V (200-240V is acceptable), 3P, 68A
(Current can be as high as 87 amps with all options ordered - CTS (+14A), 4th axis (+5A))
208V (200-240V is acceptable), 3P, 68A
(Current can be as high as 87 amps with all options ordered - CTS (+14A), 4th axis (+5A))
208V (200-240V is acceptable), 3P, 93A
(Current can be as high as 112 amps with all options ordered - CTS (+14A), 4th axis (+5A))
208V (200-240V is acceptable), 3P, 93A
(Current can be as high as 112 amps with all options ordered - CTS (+14A), 4th axis (+5A))
Power requirements
Standard (208V)
12K Spindle
208V (200-240V is acceptable), 3P, 69A
(Current can be as high as 88 amps with all options ordered - CTS (+14A), 4th axis (+5A); includes cooler current)
208V (200-240V is acceptable), 3P, 69A
(Current can be as high as 88 amps with all options ordered - CTS (+14A), 4th axis (+5A); includes cooler current)
208V (200-240V is acceptable), 3P, 69A
(Current can be as high as 88 amps with all options ordered - CTS (+14A), 4th axis (+5A); includes cooler current)
208V (200-240V is acceptable), 3P, 96A
(Current can be as high as 115 amps with all options ordered - CTS (+14A), 4th axis (+5A); includes chiller current)
208V (200-240V is acceptable), 3P, 96A
(Current can be as high as 115 amps with all options ordered - CTS (+14A), 4th axis (+5A); includes chiller current)
Power requirements
Optional (480V)
8K Spindle
480V with transformer option (432-528V is acceptable), 3P, 46A
46 amps based nominal rated current of transformer
480V with transformer option (432-528V is acceptable), 3P, 46A
46 amps based nominal rated current of transformer
480V with transformer option (432-528V is acceptable), 3P, 46A
46 amps based nominal rated current of transformer
480V with transformer option (432-528V is acceptable), 3P, 48A
(Current can be as high as 57 amps with all options ordered - CTS (+6A), 4th axis (+3A))
480V with transformer option (432-528V is acceptable), 3P, 48A
(Current can be as high as 57 amps with all options ordered - CTS (+6A), 4th axis (+3A))
Power requirements
Optional (480V)
12K Spindle
480V with transformer option (432-528V is acceptable), 3P, 46A
46 amps based nominal rated current of transformer
480V with transformer option (432-528V is acceptable), 3P, 46A
46 amps based nominal rated current of transformer
480V with transformer option (432-528V is acceptable), 3P, 46A
46 amps based nominal rated current of transformer
480V with transformer option (432-528V is acceptable), 3P, 49A
(Current can be as high as 58 amps with all options ordered - CTS (+6A), 4th axis (+3A); includes chiller current)
480V with transformer option (432-528V is acceptable), 3P, 49A
(Current can be as high as 58 amps with all options ordered - CTS (+6A), 4th axis (+3A); includes chiller current)
Maximum weight of workpiece 880 lbs 1,320 lbs 1,760 lbs 2,200 lbs 2,640 lbs
Height of table from bottom of bed*** 38″ 38″ 38″ 38.37″ 38.37″
Min. spindle nose to table distance **** 3.5″ 3.5″ 3.5″ 2.25″ 2.25″
Max. spindle nose to table distance **** 23.50″ 23.50″ 23.50″ 28.75″ 28.75″
Distance of tool carousel to table 18″ 17.50″ 17.50″ 21.50″ 21.50″
Spindle center to spindle head casting face 16.50″ 18.25″ 18.25″ 27.56″ 27.56″
Min. machine height *** 90″ 90″ 90″ 105″ 105″
Max. machine height (head all the way up) *** 106.5″ 106.5″ 106.5″ 120.5″ 120.5″
Overall width of machine with side doors open, auger chute and chip container in place 159″ 167.25″ 174.50″ 206.27″ 224.13″
Overall length of machine with electrical cabinet fully open 180° 146″ 152″ 152″ 156.22″ 156.22″
Footprint of machine with coolant tank & auger in place and pendant rotated 90° (width x length) 92″ x 129.25″ 97″ x 135″ 111″ x 135″ 133.86″ x 144.76″ 157.48″ x 144.76″
Weight net / shipping (lbs) 7,260 / 7,600 8,360 / 8,700 9,900 / 10,300 14,300 / 15,000 16,500 / 17,000
Coolant capacity 56 gal 56 gal 56 gal 71 gal 71 gal
Coolant pump and wash power 750 Watt 750 Watt 750 Watt 750 Watt 750 Watt
Air - CFM (at 90 psi), SCFM 2.5 CFM, 18 SCFM 2.5 CFM, 18 SCFM 2.5 CFM, 18 SCFM 3.0 CFM, 25 SCFM 3.0 CFM, 25 SCFM
Air quality Air dried/water separator upstream of TMC Air dried/water separator upstream of TMC Air dried/water separator upstream of TMC Air dried/water separator upstream of TMC Air dried/water separator upstream of TMC
Lubrication pump capacity 2 liter 2 liter 2 liter 2 liter 2 liter
Specifications subject to change. *** Height changes slightly based on how machine is leveled on leveling screws. **** Can vary slightly due to home switch location and soft limit settings.

Options

Machine Options

Part Probe

Part Probe

Renishaw® OMP40-2 Inspection Probe and OMI-2T Optical Receiver

The OMP40-2 Inspection Probe is a compact probing solution that uses a kinematic mechanism able to achieve a repeatability of 1 µm. The probe interfaces with the OMI-2T Optical Receiver that mounts inside the TMC. Both devices are included in the Part Probing option.

You use the Probe with the Electronic Handwheels as a productive way to replace edge finders for touching off parts and fixtures. The option works in the DRO Mode of the ProtoTRAK RMX CNC to set offsets using the ABS SET and INC SET features. You can also use it with the Center feature to easily calculate line lengths and diameters of circles.

Haimer<sup>®</sup> Universal 3D Sensor

Haimer® Universal 3D Sensor

The Haimer® Universal 3D Sensor lets you quickly find edges in X and Y relative to the center of the spindle. Unlike a standard edge finder, it is unnecessary to allow for the diameter of the probe. Simply bring the dial to zero, and you are finished. The sensor also allows you to find the part in Z.

TRAKing<sup>®</sup> / Electronic Handwheels

TRAKing® / Electronic Handwheels

The feel of manual control of real handwheels, but our electronic handwheels bring the power of the CNC to your fingertips through features such as TRAKing and DO ONE.

4th Axis

4th Axis

The TRAK® 4th axis system for Toolroom Machining Centers provides full control of 4th axis machining and engraving through the ProtoTRAK RMX CNC. The system can also be used as an indexer. Includes 8″ three-jaw chuck. Optional tailstock sold separately.

Tailstock - 4th Axis

Tailstock - 4th Axis

Support for longer workpieces. This option is sold separately.

4th Axis Ready

4th Axis Ready

The electrical cabinet is pre-wired for the optional 4th axis rotary unit. You would want this to have each machine in your shop able to run the 4th axis and then swap the actual rotary unit between them. It also enables the installation of the option on the machine later without a lot of downtime or expense.

Coolant Through Spindle

Coolant Through Spindle

The TRAK CTS system provides pressurized coolant to remove chips during drilling and tapping work. Compared to flood coolant, the CTS option can increase tool life, allow for higher spindle speeds and a corresponding reduction of cycle times, and allow for better surface finishes.

12,000 RPM Spindle

12,000 RPM Spindle

The optional 12,000 RPM spindle features ceramic bearings, and a spindle cooler to minimize temperature rise when running for long periods of time.

Remote Stop/Go Switch

Remote Stop/Go Switch

A hand-held switch to stop and continue program run. Available for purchase at our service parts website: Remote Stop/Go Switch

Tooling Cart & Preset Tool

Tooling Cart & Preset Tool

Huot® ToolScoot cart and preset tool. Tools not included.

Fixture Cart

Fixture Cart

Heavy-duty cart for the set up and transportation of fixtures.

Tooling Grippers - BT40

Tooling Grippers - BT40

Set of 16. Includes mounting hardware.

Retention Knobs - CAT40

Retention Knobs - CAT40

For CAT40 tooling. Set of 16.

Kurt<sup>®</sup> Vise

Kurt® Vise

6″ Kurt vise and mounting hardware - model DX6. Opens to 9″.

TRAK<sup>®</sup> USB Memory

TRAK® USB Memory

The USB Memory option consists of an industrial-grade Delkin® Thumb drive. This device is unsurpassed for reliability and speed of file access and is the storage of choice for our own software engineers.

VIDEO: TRAK® USB Memory Option Overview

Other TMC Options

Other TMC Options

  • Internal Memory Drive
  • Transformer Option
Extended Warranty

Extended Warranty

TRAK offers a 2 year extended warranty for this product.

Software Options

Clear Off

Clear Off

Clear Off allows for the removal of part material from the outside in, leaving only the bosses and profiles you want. This option is easily programmed at the machine, and works with both DXF and Parasolid models.

VIDEO: Clear Off Programming Demo | ProtoTRAK RMX CNC

CAM File Out Converter

CAM File Out Converter

Write, save and then run programs with RX Canned Cycle Events on Legacy ProtoTRAK controls in either .CAM Events or .GCD format.

Offline Programming

Offline Programming

  • ProtoTRAK RX user interface for Windows® PC
  • Program parts and simulate CNC Run
  • Modify files from current and former ProtoTRAK models

VIDEO: Installing ProtoTRAK Offline Software

MTConnect<sup>®</sup>

MTConnect®

The TRAK MTConnect option enables customers to add MTConnect functionality quickly and easily to their machines, so that machine data can be collected using the standard MTConnect protocol.

  • Machine networking through ethernet connection or USB Wi-Fi adapter
  • Collect machine data throughout shop
  • Monitor machine status, receive notifications and analyze data throughout your machines’ history

3rd party software not included.

VIDEO: MTConnect® Option Overview

Parasolid File Converter

Parasolid File Converter

  • Import and convert 3D CAD data into ProtoTRAK programs
  • X_T files
  • X, Y & Z dimensions are transferred into program events
  • 2D and 3D views of part
  • Add or remove geometry
  • Chaining
  • Easy, prompted process you can do right at the machine
DXF Converter

DXF Converter

  • Import and convert CAD data into ProtoTRAK programs
  • DXF or DWG files
  • Chaining
  • Automatic Gap Closing
  • Layer control
  • Easy, prompted process you can do right at the machine
Auxiliary Functions

Auxiliary Functions

Enables programming and control of:

  • Pulse indexer (optional)
  • Auxiliary output to control optional secondary device

Software

Software Features - General Operation

  • Enhanced ProtoTRAK Assistance (EPA)
    • Context responsive help with control operations
    • Step-by-step instructions, diagrams and videos
  • Watch Me videos for quick introduction to ProtoTRAK RMX operation
  • What’s New videos for quick review of upgraded features in new releases
  • Clear, uncluttered screen display
  • Fly out windows for quick access to features and info
  • Programming Defaults to simplify part programming
  • User profiles for Defaults
  • Event Options to modify Defaults or select additional functionality
  • QWERTY touchscreen keyboard
  • Calculator
  • Prompted data inputs
  • English language – no codes
  • Soft keys - change within context
  • Windows® operating system
  • Selectable two or three-axis CNC
  • Color graphics with adjustable view
  • Gestures for pan, zoom, rotate
  • Inch/mm conversion
  • Convenient modes of operation
  • Networking

Program Mode Features

  • Circular interpolation
  • Linear interpolation
  • Advanced Adaptive Tool Path
  • Geometry programming
  • Toolpath programming
  • Auto Geometry Engine® (A.G.E.) – Built-in CAD to fill in missing print data
  • Alphanumeric program names
  • Automatic Scaling of print data
  • Nesting
  • Multiple Fixtures
  • Incremental and absolute dimensions may be mixed on a single point
  • Automatic diameter cutter comp
  • Program data editing
  • Part graphics update while programming
  • Selectable display between size of drawing and number of events
  • List Step graphics relate Events to Drawing
  • Editing of programmed data
  • Swipe to move through programmed Events

DRO Mode Features

  • Incremental and Absolute dimensions
  • Graphical Override of Axis Feed and Spindle RPM
  • Jog at rapid with override
  • Power feed X, Y or Z
  • Teach-in of manual moves
  • Programmable Go To dimensions
  • Servo return to 0 absolute
  • Tool offsets from Tool Library
  • Line Center calculation
  • Circle Center calculation

Canned Cycles (Event types)

  • Position
  • Drill / Bore / Tap /Helical Drill
  • Bolt Hole Drill / Bore / Tap / Helical Drill
  • Mill
  • Arc
  • Circular profile
  • Rectangular profile
  • Irregular Profile (with Auto Geometry Engine)
  • Face Mill
  • Circle pocket / Rectangular pocket
  • Irregular Pocket (with Auto Geometry Engine)
  • Islands including Pocket and Island shapes
  • Subroutine Repeat /Mirror / Rotate
  • Subroutine Convert Drill to Tap
  • Copy - Mirror / Rotate / Convert Drill to Tap
  • Helix
  • Auxiliary - Part Change Position, Coolant On/Off, Air On/Off
  • Engrave - Horizontal / Radial / Vertical / Mirror
  • Thread Mill
  • Program pause

Advanced Features

  • Adaptive Pocket Roughing
  • Verify Make Part – solid model simulation of programmed toolpath
  • Finish Tool #
  • Rest Machining
  • Multiple Fixture Offsets
  • Event Comments
  • G-code editor
  • Search Edit
  • Tool Library Flyout Window
  • Automatic Tool Syncing between carousel, program and library tools
  • Pictures and notes saved in Part Programs
  • Save and Open Temp
  • Program I/O Look
  • Chip Clear
  • Clipboard

Offline Programming Option

Optional Feature
  • ProtoTRAK RMX user interface for Windows PC
  • Program parts and simulate CNC Run
  • Modify files from current and former ProtoTRAK models

DXF File Converter Option

Optional Feature
  • Import/convert CAD data into ProtoTRAK programs
  • DXF or DWG files
  • Chaining
  • Automatic Gap Closing
  • Layer control
  • Easy, prompted process right at the machine
  • Island and Profile Events

Parasolid File Converter Option

Optional Feature
  • Import and convert 2.5D CAD data into ProtoTRAK programs
  • X_T files
  • X, Y and Z dimensions are transferred into program events
  • 2D and 3D views of part
  • Add or remove geometry
  • Chaining
  • Easy, prompted process you can do right at the machine
  • Island and Profile Events

TRAK® MTConnect Option

Optional Feature
  • Machine networking through ProtoTRAK® ethernet connection or USB Wi-Fi adapter
  • Collect machine data throughout shop
  • Monitor machine status, receive notifications and analyze data throughout your machine history

Auxiliary Functions Option

Optional Feature
Enables programming and control of:
  • Pulse indexer (optional)
  • Auxiliary output to control optional secondary device

CAM File Out Converter Option

Optional Feature

Write, save and then run programs with RX Canned Cycle Events on Legacy ProtoTRAK controls in either .CAM Events or .GCD format.

Clear Off Option

Optional Feature

Clear Off allows for the removal of part material from the outside in, leaving only the bosses and profiles you want. This option is easily programmed at the machine, and works with both DXF and Parasolid models.

Videos

TRAK Toolroom Machining Center feat. the ProtoTRAK RMX CNC
TRAKing and the Electronic Handwheels Option for the TRAK Toolroom Machining Center
Introducing The World’s First Toolroom Machining Center
MTConnect Option for ProtoTRAK RX Series Machines
TMC Demo: Toolroom Ops & Production Ops | ProtoTRAK RMX

Other TRAK Toolroom Machining Center Models:

TRAK TMC5 Toolroom Machining Center
TRAK TMC5 Specifications:
  • Table Size: 27.56″ x 15.75″
  • Travel (x, y, z): 20″ x 16″ x 20″
  • Footprint: 85″ x 129.25″
  • Horsepower: 15/10
TRAK TMC10 Toolroom Machining Center
TRAK TMC10 Specifications:
  • Table Size: 44.09″ x 19.69″
  • Travels (x, y, z): 40.75″ x 20″ x 20″
  • Footprint: 111″ x 135″
  • Horsepower: 15/10
TRAK TMC12 Toolroom Machining Center
TRAK TMC12 Specifications:
  • Table Size: 51.18″ x 23.62″
  • Travels (x, y, z): 50″ x 27″ x 25″
  • Footprint: 133.86″ x 144.76″
  • Horsepower: 22.5/15
TRAK TMC14 Toolroom Machining Center
TRAK TMC14 Specifications:
  • Table Size: 62.99″ x 23.62″
  • Travels (x, y, z): 60″ x 27″ x 25″
  • Footprint: 157.48″ x 144.76″
  • Horsepower: 22.5/15